SR 100HL – AC/DC Power Supply 100W with Comms
- Ideal as a standby float charging of lead-acid batteries
- Constant current limit and Precise voltage control
- Temperature compensation option
- Optional Communication Port: RS232 , RS485, Modbus RTU & SNMP , webpages
- Power loss & battery system alarms
- Rugged design and construction for long life and challenging environments
- Description
- SERIES TABLE
- SPECIFICATIONS TABLE
- OPTIONAL FEATURES
- MODBUS & SNMP DOWNLOADS
- MODELS REPLACED BY SR100HL
SR100HL – 100W
AC/DC Power Supply/Battery Charger
The SR100HL range is designed for use as a reliable and stable AC to DC power supply, or float charger for lead-acid batteries. Note that for float charging the output voltage must be set to approximately 15% above the nominal battery voltage models. This is done as the default voltage for the 12V model but must be specified at time of order for all higher voltage models.
Applications
- Security – Access Control
- Industrial Processes Switching Protection
- SCADA
- Radio Repeaters – Remote Sites
Points of Difference
- Ideal for standby float charging of lead-acid batteries
- Constant current limit and Precise voltage control
- Temperature compensation option
- Efficient modern “current mode”
- Relay Alarms Output
- Suitable for parallel operation
- Rugged design and construction for long life and challenging environments
Optional Features
- American Input Voltage 110 VAC ( 88 – 135 VAC)
- Communication Port ( RS232 ASCII – SR485 – MODBUS RTU – SNMP , webpages)
- Digital Input/Outputs: Customizable 3 digital inputs & 1 digital output.
- Mounting: DIN rail , Rack Mount 19″ with V/I meter available, Wall mount
- N+1 redundancy
- Boost Charger
SR100HL – 100w – Power Supply/Battery Charger with optional comms
SERIES TABLE
| MODELS | Power Supply | Battery Charger* | Adjustable range (V) | ||
| Output Volts (factory default) | Output Current (A) (continuous) | Output Volts* (Charging) | Output Current (A) (Charging) | ||
| SR100HL12 | 13.8 | 7.3 | 13.8 | 7.3 | 11-14 |
| SR100HL24 | 24 | 4.2 | 27.6 | 3.6 | 22-28 |
| SR100HL30 | 30 | 3.3 | 34.5 | 2.9 | 27-33 |
| SR100HL36 | 36 | 2.8 | 41.4 | 2.6 | 34-43 |
| SR100HL48 | 48 | 2.1 | 55.2 | 1.8 | 45-57 |
SPECIFICATIONS TABLE
| Output power | 100W (0-50°C ) |
| Input Voltage | 180V – 264VAC 45-65Hz |
| Output Voltages | 13.8V, 24, 30V, 36V, 48 VDC |
| Other voltages by request | |
| Voltage Adj. Range | 85% – 105% of Vout |
| Frequency | 45-65Hz |
| Overcurrent protection | Constant current limit under overload and short circuit conditions |
| Isolation | Input – earth – 2.5KVdc |
| Output – earth – 500Vdc | |
| Efficiency | > 85% |
| Inrush Current | < 30A , 1.8ms |
| Operating temperature | -20 to 50 °C ambient at full load |
| Humidity | 0 – 95% relative humidity non – condensing |
| Cooling | Natural convection |
| LED Indication | Green: DC OK |
| Green: Power OK | |
| Alarms Relay | Form C contacts changeover, rated 30VDC,2A/110VDC,0.3A/125VAC,0.5A |
| DC Hight () | |
| POWER (main fails, PSU fail) | |
| DC Low () | |
| Line Regulation | <0.04% over input range |
| Load Regulation | <0.5% open circuit to 100% load |
| Noise | <0.3% |
| Transient response | 200mV over/undershoot, |
| Load step 20-100%, 400us settling time | |
| Hold-up time | 15-20 ms (nom-max. Vin) without battery |
OPTIONAL FEATURES
| Optional Input Voltage | 88 – 132 VAC |
| Communication Port | RS232 (ASCII) |
| RS485 (ASCII) | |
| Modbus Serial | |
| SNMP, Webpages | |
| Inputs/Outputs | Customizable 3 Digital Inputs and 1 Digital Output |
| Temp. Compensation | Temperature sensor on 1.7m lead with adhesive pad: -4mV / °C / cell ±10% |
| Mounting | DIN Rail |
| Standalone | |
| 19”Rack Mount – Optional V/I meter for subrack : SR-Meter | |
| N+1 Redundancy | Using 2 chargers each with its own battery |
| Boost Charger | Customizable feature on |
