ZUP Series

Lab Bench DC Power Supply 200W-800W

The ZUP series are wide range output switching power supplies with laboratory performance. The ZUP series is power factor corrected and operates from worldwide AC voltage range continuously. Output voltage and current are continuously displayed and LED indicators show the complete operating status of the power supply.The front panel controls allow the user to set the output parameters, the protection levels (over-voltage / under-voltage)and arm the foldback protection to disable the output if the unit switches from Constant-voltage mode to Constant-current mode.

Control via the serial communication port

The following parameters can be programmed via the serial communication port:

  1. Output voltage setting
  2. Output current setting
  3. Output On/Off
  4. Arming or release of the foldback protection
  5. Over-voltage protection setting
  6. ‘Soft’ under-voltage limit
  7.  Output voltage measurement
  8. Output current measurement
  9. Power supply start-up mode (last setting or safe mode)
  10. Over-voltage protection setting read
  11. Under-voltage limit read
  12. Remote/Local Control

Output connections

Output connections are made to rear panel bus-bars. Either the positive or negative terminal may be grounded or the output may be floated. The maximum potential (including the output voltage) that either output terminal is from ground must not exceed 60V. Local or remote sense may be used. In remote sense, the maximum voltage drop on each wire is 0.5V.

SERIES TABLE

ModelOutput Voltage ( VDC )Output Current ( A )Output Power ( W )
ZUP6-330 ~ 6 VDC0 ~ 33198
ZUP6-660 ~ 6 VDC0 ~ 66396
ZUP6-1320 ~ 6 VDC0 ~ 132792
ZUP10-200 ~ 10VDC0 ~ 20200
ZUP10-400 ~ 10VDC0 ~ 40400
ZUP10-800 ~ 10VDC0 ~ 80800
ZUP20-100 ~ 20VDC0 ~ 10200
ZUP20-200 ~ 20VDC0 ~ 20400
ZUP20-400 ~ 20VDC0 ~ 40800
ZUP36-60 ~ 36VDC0 ~ 6216
ZUP36-120 ~ 36VDC0 ~ 12432
ZUP36-240 ~ 36VDC0 ~ 24864
ZUP60-3.50 ~ 60VDC0 ~ 3.5210
ZUP60-70 ~ 60VDC0 ~ 7420
ZUP60-140 ~ 60VDC0 ~ 14840
ZUP80-2.50 ~ 80VDC0 ~ 2.5200
ZUP80-50 ~ 80VDC0 ~ 5400
ZUP120-1.80 ~ 120VDC0 ~ 1.8216
ZUP120-3.60 ~ 120VDC0 ~ 3.6432

ZUP-80 & ZUP-120 have been discontinued; and replaced by the Z+ Series

SPECIFICATIONS TABLE

INPUT VOLTAGE:85 – 264VAC
FREQUENCY:47 ~ 63Hz
INPUT CURRENT (@230VAC)ZUP200W: 1.5A
ZUP400W: 2.7A
ZUP800W: 5.4A
INPUT HARMONICS:Complies with EN61000-3-2
POWER FACTOR:Corrected @ 0.99
EFFICIENCY:Model dependent: 68~84%
LOAD REGULATION:0.01%  +3mV (CV)
0.02%  +5mA (CC)
LINE REGULATION:0.01%  +2mV (CV)
0.01%  +2mA (CC)
RIPPLE:5mV rms (CV) 7.5-100mA (CC)
PROTECTION:• Over voltage
• Over temperature
• Over current foldback

You may also like...