Do you already have a cabinet installed? No worries !!!Our comprehensive standalone range of products can be customised in 19” Rack Mount.
LOW DC POWER APPLICATIONS
Low DC Power Applications
19" Rack Mount Solutions
- DC Output voltage of 27.6V
- Modbus RS485, RS232 communication
- Bat Con TEST , Main Fail and Bat Sys Alarms
- LVD ( Low Voltage Disconnect).
- 2 x ICT103048-5AI2 190W 11-30/48VDC.
- Input Voltages from 11 – 30VDC.
- DC distribution: 4 x 2A MCB’s.
- Equipped with a P50 Blocking diode for redundancy applications.
- Temperature compensation.
- Battery low voltage disconnect.
- SNMP.
- Comprehensive battery monitoring
- Digital V/I meter monitors the output of the charger.
- Auxiliary , Mains Fail , Battery Low alarms with voltage free contacts.
AC/DC 650W power supply. Provides a number of outputs via special Lemo connectors on rear panel. A number of LED’S on the front panel provide visual indication of all outputs, together with special DC filtering.
This special battery charger was designed for use in remote areas in the Pacific powering special scientific instruments. Input is 36-75VDC and output 13.8 VDC 50W charging a battery for stand-by power. A number of digital meters provide user with critical information and all connections are on special MIL-SPEC connectors.
Designed to customer specifications for the mining industry, this comprises of three separate 3U x 19in Rack power supplies. The AC/DC unit provides 24V 35A for battery charging. The DC/DC unit provides 24/48V 500 watts and , together with a Remote Monitoring unit.
- Power Supply Output set to 48 VDC.
- DC High, Mains Fail, and DC Low alarms on voltage free contacts for each power supply ( NO,COM ,NC)
- 4-way Phoenix connectors for DC Load outputs.
- Front removable power supplies.
- 3X5A MCB’s load outputs with frontal access.
- 100Ah backup.
- 6 x 2amp fused with series diode outputs. (Screw terminals).
- Fuse blown or output o.k LED’s
- Link selectable sink/source trigger.
- Lockable steel cabinet with screw connect tamper switch.
- 250watt four stage smart charger with integral clean contacts for mains fail/batt low.
- Complete system. Only requires trigger, output and mains connections
- Battery and battery cables supplied
- 2.2kW 110 VDC float Charger.
- Two 1.1kW Hot Swappable rectifiers.
- Fully programmable touch screen controller.
- Single Phase 230VAC input protected by surge protection monitored by the system.
- 32A 2 pole Battery Breaker monitored by the system.
- 32A DC Output Breaker monitored by the system
- DC High, Battery Low, AC Mains High/Low, Rectifier Fail, System Major Earth Fault and Controller Fail Programmable alarms on voltage-free relay contacts.
- SEC-SR wall mount cabinet with dimensions 405H x 444W x 273D mm.
- 750W 24VDC power supply.
- Digital V/I meter.
- 24V DC Input terminals for redundant applications.
- Mains Fail, DC Low and Tamper alarms in the form of voltage free contacts.
- 4 x 10A 1P Distribution MCB’s
- 6A 1P Mains Input MCB.
- 6U 500W 24VDC Wall Mount Battery Charger
- 6A Mains Input MCB
- P50 Output Diode
- 32A 2P Charger Output MCB
- Digital V/I monitoring the Output
- 32A 1P Load Output MCB
- 32A 1P Battery MCB
- Load LVD
- Mains Fail, DC High, DC Low, System DC Low and General Alarm on voltage-free relay contacts.
125VDC up to 2.2kW Single Phase Wall Mount.
Can be used as stand-alone power supply without batteries.
Single phase surge protection incorporated.
Hot swappable power modules.
Convection cooled system.
Common Form C alarm relay contacts (6).
Using marine grade aluminium to protect from corrosion, our pole mounted enclosures are engineered to accommodate electrical powering equipment, racked in a pole mount configuration. Our custom designed pole mount solutions can be made to suit your requirements and can either house batteries inside the cabinet, or for a more compact solution can house batteries separately in an underground box.
Low DC Power Applications - Cabinets
With Helios Power Solutions the ability to customise is always an option, ensuring our products meet your every specification, in turn providing a robust reliable and proven solution.
Some areas of customization include IP & Seismic rated, Special terminations/ connections, Remote monitoring & control, Load control & selectivity just to name a few
- 500W 24VDC Battery Charger
- 18U x 600mm x 600mm cabinet with top entry
- Digital volt and ammeter to monitor DC output
- LVD (low voltage disconnect)
- 24V 150Ah battery bank
- Rectifier Fail, Earth Fault, DC High and DC Low alarms
- DC Distribution with 1 x 10A and 3 x 4A MCB’s.
- 24VDC 250W redundant charger in 2U rack
- 30VDC 250W redundant charger in 2U rack
- Individual AC inputs for all rectifiers
- 24VDC distribution of 2 x 2A 2P and 3 x 6A 2P MCB’s
- 30VDC distribution of 1 x 20A 2P and 4 x 6A 2P MCB’s
- Two digital V/I meters and two alarm cards monitoring the 24VDC and 30VDC output voltages
- Two battery shelf housing the 24VDC and 30VDC battery banks
- DC High, Mains Fail and DC Low alarms for each rectifier
- DC High, DC Low and Earth fault alarms for the 24VDC system and a second set for the 30VDC system.
- 24VDC 250W redundant charger in 2U rack
- 30VDC 250W redundant charger in 2U rack
- Individual AC inputs for all rectifiers
- 24VDC distribution of 2 x 2A 2P and 3 x 6A 2P MCB’s
- 30VDC distribution of 1 x 20A 2P and 4 x 6A 2P MCB’sTwo digital V/I meters and two alarm cards monitoring the 24VDC and 30VDC output voltages
- Two battery shelf housing the 24VDC and 30VDC battery banks
- DC High, Mains Fail and DC Low alarms for each rectifier
- DC High, DC Low and Earth fault alarms for the 24VDC system and a second set for the 30VDC system
- 2.2kW 110 VDC float Charger.
- Two 1.1kW Hot Swappable rectifiers.
- 47U cabinet.
- Combined Major and System Fail alarms with voltage free contacts.
- Internal 108V 105Ah battery bank protected with a 40A 2P MCB.
- DC Distribution with 4 x 2P 20A and 1 x 2P 10A breakers.
- Remote monitoring and programming with a webpage interface.
- SNMP v2.5 via Ethernet.
- Email reporting.
- 1.6kW 108VDC charger expandable to 4.8kW
- 38U floor mount 19” cabinet.
- DC Distribution with 12 x 10A 2P MCB’s.
- Remote control with MODBUS and SNMP.
- Temperature compensated charging.
- Battery Management.
- Temperature sensor.
- Hot Swappable convection cooled rectifiers.
- Mains Fail, DC Low, DC High and General System alarms.
